Intelli-G Int-Meter timer function

Issues received from our customers with detailed answer and solution

Moderator: RusuP

User avatar
User
Posts: 8
Joined: Mon Mar 18, 2019 1:19 pm

Intelli-G Int-Meter timer function

Postby User » Wed Jun 05, 2019 12:32 pm

Dear Intelli-G Team,



I’m able now to control the ISO and Shutter (very nice!!!), but regrettably not the Int-Meter start/stop or the Int-Meter timer function.

These two functions are fundamental for acquiring images. After changing the recommended settings it is not possible any more to trigger the camera with ground station pro.



Is there any guide available how to use the Int-Meter start/stop or the Int-Meter timer correctly? I used the searched function without any success.

Can I use this function with my Sony Alpha 7R III ?



Thank you !

User avatar
RusuP
Technical Support
Posts: 32
Joined: Thu Aug 11, 2016 3:33 pm
Location: Brasov
Contact:

Re: Intelli-G Int-Meter timer function

Postby RusuP » Wed Jun 05, 2019 2:00 pm

Hi ,

You can use our Int-Meter function with almost all supported cameras, including Sony Alpha 7R III . Please make sure that you have 2 channels free on your Remote Controller/Dji Expansion Kit in order to calibrate them in Intelli-G Application. These channels need to be :

1 x Two position Switch (in my case SC), this channel will be used for Int-Meter start/stop function.
1 x Three position Switch (in my case SH) , this channel will be used for Int-Meter timer function. With this channel, you change the shutter interval between 1 - 10s


STEP 1 : Configure your Remote Controller :

In the MIXER page, you will need to setup those two channels (SC , SH in my case):
Image

STEP 2 : Connect and configure the Intelli-G device

1. Insert the Setup Plug. You may use any connector with Dupont female ends, not necessarily the one provided with Intelli-G, to connect the Setup pin to any of the GND pins on the device. Power the Intelli-G on.

⭐ Note: In case you have prepared the device to enter in Setup Mode or the device has not yet been configured, it should now be in Setup Mode. This is indicated by the LED blinking purple. Otherwise, connect the Setup pin to any of the GND pins on the device.

Image

2. Power everything up and connect to your Intelli-G device using our Intelli-G mobile app.

3. Select the Intelli-G SSID from the W-iFi list (only for IOS users):

Image

4. Return to the Intelli-G mobile app and select “W-iFi SETUP READY“

Image

5. Select your input connection type, according to the protocol intended to be used. In our case, it will be SBUS Boost protocol.
⭐ Note: If you have interferences on SBUS you can use SBUS Boost for a better calibration .
Image

6. In order to calibrate the input channels, pass each of them through the physically available positions, actioning them at a slow pace. To ensure proper usage, make sure all the Slider-type input controls, are positioned on their centers, close to the 0 value of the interval.
In case momentary switches (push buttons) are used, please mark the channel by pressing its position once.

⭐ Note: Make sure that you don't forget to select SBUS 1 as momentary . Otherwise, the REC/Shutter trigger will not work!
Image

7. After finishing CALIBRATION, choose the camera type and output connection protocol. For Wi-Fi protocol, fill in the camera information: SSID, Password, and IP (default IPs are automatically suggested). Alternatively, you can scan the QR code exposed by the Wi-Fi screen on the camera and the camera information will be automatically filled in.
Image

Select Int-Meter start/stop function on SBUS 1 and Int-Meter Timer on SBUS 2 :
Image

8. Save Mapping and Upload your Configuration.

9. Remove the Setup Plug and reset the device . The Intelli-G device will blink GREEN (trying to connect to camera Wi-Fi).

10. Now you will be able to Start/Stop the Intervalometer with SC switch. In order to change the interval, please make sure the SH switch (3 pos SW) is in the middle position, by moving to up or down position and return to center you will increase or decrease the interval by 1 second .
WhatsApp +40751973175 (Monday to Friday 09:00AM- 05:00PM (GMT +2:00))

Balamur
Posts: 2
Joined: Wed Jun 05, 2019 3:14 pm

Re: Intelli-G Int-Meter timer function

Postby Balamur » Wed Jun 05, 2019 3:18 pm

Dear Resu,

Thanks for your fast answer.

Regrettably I did everything what is described there (difference only DJI Lb2 +Expansion Kit, see below) and there was no reaction when I want to use the Int-Meter function.
Here you can see the information with DJI Lb2 +Expansion Kit

Screenshot_2019-06-05-13-48-29-536_com.diginesis.intellig.png

Screenshot_2019-06-05-13-47-47-234_com.diginesis.intellig.png


The Sbus4 is not defined as on/off, is that maybe the reason? Is there any possible to change that?
More over, the Sbus4 is stable at one position you maybe know. I also tried to hold the other position, but also then the Int-Meter start/stop doesn’t work.
Any idea?

Best wishes,
Norman Wilke

User avatar
RusuP
Technical Support
Posts: 32
Joined: Thu Aug 11, 2016 3:33 pm
Location: Brasov
Contact:

Re: Intelli-G Int-Meter timer function

Postby RusuP » Wed Jun 05, 2019 4:09 pm

Hi Norman,

This might be the problem, our Intelli-G device needs to know that SBUS 4 is a Momentary Switch .

In order to define SBUS 4 as ON/OFF, you need to recalibrate all channels and redo the mapping. This time please use SBUS Boost instead SBUS, this will help you with your calibration .

The Intelli-G App will let you know when you need to select all momentary switches to mark them as momentary :

Image

Please let us if this fix your problem.

Best regards,
Intelli-G TEAM
WhatsApp +40751973175 (Monday to Friday 09:00AM- 05:00PM (GMT +2:00))

Balamur
Posts: 2
Joined: Wed Jun 05, 2019 3:14 pm

Re: Intelli-G Int-Meter timer function

Postby Balamur » Wed Jun 05, 2019 6:47 pm

Fixed the issue! Thanks a lot for the good support

Janhot
Posts: 10212
Joined: Thu Mar 12, 2020 7:44 pm
Location: Ethiopia
Contact:

Viagra Online Kaufen Legal MatHeptiz

Postby Janhot » Mon Mar 16, 2020 3:29 pm

Venta Cialis Barcelona Buy Cialis Homeopathic Amoxicillin For Pets <a href=http://apcialisle.com/#>Buy Cialis</a> Propecia Generico Madrid

Janhot
Posts: 10212
Joined: Thu Mar 12, 2020 7:44 pm
Location: Ethiopia
Contact:

Antibiotics For Sale MatHeptiz

Postby Janhot » Mon Mar 16, 2020 3:29 pm

Achat Amoxicillin Prescrire United Nations Medicament Cialis Treat Acne With Amoxicillin <a href=http://apcialisle.com/#>Buy Cialis</a> Mexico Pharmacy Mail Order Online

Janhot
Posts: 10212
Joined: Thu Mar 12, 2020 7:44 pm
Location: Ethiopia
Contact:

Herbal Propecia MatHeptiz

Postby Janhot » Mon Mar 16, 2020 3:30 pm

Finasteride 10mg No Prior Script cialis for sale Comprimes Cialis <a href=http://apcialisle.com/#>Buy Cialis</a> Generic Lasix

Janhot
Posts: 10212
Joined: Thu Mar 12, 2020 7:44 pm
Location: Ethiopia
Contact:

Vente Propecia 1mg MatHeptiz

Postby Janhot » Mon Mar 16, 2020 3:30 pm

Cialis Potenzmittel Rezeptfrei cialis 20mg price at walmart Levitra Posologie <a href=http://apcialisle.com/#>Cialis</a> Viagra Online Overnight Delivery

Janhot
Posts: 10212
Joined: Thu Mar 12, 2020 7:44 pm
Location: Ethiopia
Contact:

Buy Zithromax To Treat Chlamydia MatHeptiz

Postby Janhot » Mon Mar 16, 2020 3:31 pm

Cialis Parapharmacie cialis Doxycycline Over Night <a href=http://apcialisle.com/#>Buy Cialis</a> Acheter Misoprostol En Ligne Moin Cher


Return to “Frequently Intelli-G Issues”

Who is online

Users browsing this forum: DenishaRi, GlennSal, KathieDe and 28 guests